Home
/
Toshiba
/
Tecra R10
/
Maintenance Manual

Toshiba Tecra R10, Maintenance Manual, Page: 115 / 388

Share

Page: 115 / 388

Toshiba Tecra R10 Maintenance Manual Download Page 115

2.20 Intel Turbo Memory Troubleshooting U(Not Used)U

2 Troubleshooting Procedue

2.20 Intel Turbo Memory Troubleshooting (Not Used)

To check if Intel Turbo Memory is malfunctioning or not, follow the troubleshooting
procedures below as instructed.

Procedure 1: Check on Windows OS

Procedure 2: Connector Check and Replacement Check

Procedure 1

Check on Windows OS

Use the software, Intel Turbo Memory Console, which is originally prepared in the computer
to check if the Intel Turbo Memory is operating without problems.

Start the Intel Turbo Memory Console and confirm the followings:

Check marks are attached to “Enable Windows ReadyBoost” and “Enable Windows
ReadyDrive”.

The values for “Windows ReadyBoost” and “Windows ReadyDrive” are “Enabled” and
“Total Cache Size” is “4GB”.

TECRA R10 Maintenance Manual (960-708)

[CONFIDENTIAL] 2-65

«
...
113
114
115
116
117
...
»

Summary of Contents for Tecra R10





































































































































































































































































































































































































Reviews:

No comments