Toshiba Tecra R10 Maintenance Manual Download Page 245

Page: 245 / 388

4.7 Memory module

4 Replacement Procedures

Installing the Memory module

To install the memory module, make sure that the computer is powered off, follow the steps
below and refer to Figure 4-6 and 4-7.

NOTE: The slot A is reserved for the first memory module. Use the slot B for expanded

memory. If only one module is installed, use the slot A.

Insert the

memory module

into the

memory module connector

slantwise.

NOTE: Align the notch of the Memory card to the guide of the memory module

connector.

Press down the memory module gently until it is latched.

CAUTION: After installing the memory module, make sure that the memory module is

secured with the left and right latches.

Set the

memory cover

and secure it with two

screw

NOTE: When replacing the MEM COV ASSY with a new one, stick a caution label (LABEL

MEM COV) on it.

LABEL MEM COV

MEM COV ASSY

NOTE: When the power of the computer is turned on, the computer checks automatically the

memory size. Confirm that the new memory is detected correctly.
If the memory is not detected, check that it is connected correctly.

TECRA R10 Maintenance Manual (960-708)

[CONFIDENTIAL]

4-19

Summary of Contents for Tecra R10





































































































































































































































































































































































































Search results

Summary of Contents for Tecra R10

Reviews:

Brands by name

Popular brands

Toshiba Tecra R10, Maintenance Manual

Search results

Summary of Contents for Tecra R10

Reviews:

Brands by name

Popular brands