Programming by PC
Installer Manual -
TP16-256
4-38
PROGRAMMING OF THE ATTRIBUTES
To associate the attributes to the key check the relevant item.
z
By-pass general alarms
If checked, the user will be entitled to arm the system even
in presence of a general alarm (i.e. tamper, low battery,
power failure, supervision, trouble modules)
z
Automatic communicator block on disarming
If checked, upon disarming of the system (by inserting the
key into the key reader) the active telephone channels (and
those queued up) are blocked automatically.
z
Confirmation of disarming (hold-up block)
Activates the hold-up function on the key. In this case,
disarming by this key will have to be confirmed by entering
of a valid user code within a determined period of time
(disarming confirmation delay), otherwise a silent hold-up
alarm will be released.
z
Exclusion disabled
If checked, the user will
not
be entitled to arm the control
panel excluding some of the zones (both voluntary and
automatic zone exclusion are disabled). The control panel
will be armed in any case, and if there are open zones,
the alarm will be released.
z
Quick disarming
On introduction of the electronic key into the key reader,
while the control panel is armed, all the associated
programs are disarmed. In this case the electronic key will
arm/disarm only the first program associated to it.
Repeat the procedure for all the keys (1 to 64).
Once you have finished programming of the keys, press:
z
OK
to confirm and close the code configuration
tables
z
Abandon
to undo programming and close the code
configuration tables
WARNING
If you use the key reader with minikeypad TP SK6N, for arming of the program, you will have to
insert the key into the key reader and enter the program number.
In addition to the key-program association it is indispensable to associate the programs to the key
reader (see § 4.1.5), otherwise the introduction of the key will be ineffective.
Summary of Contents for TP16-256
