Sony MVS-8000X SystemMVS-7000X System, User Manual

Page: 70 / 706

USO
RESTRITO
70
Names and Functions of Parts of the Control Panel
Name Description
PST (preset)
COLOR MIX The color matte (unpatterned display) is
inserted during transition, replacing the
current video by the color matte, and then
replacing the color matte by the new video.
WIPE (DME
wipe) The current video is replaced by the new
video, using the wipe pattern selected in the
Wipe menu.
DME A wipe type of transition is carried out, using
the DME effect selected in the DME Wipe
menu.
FM1&2CLIP, A recorded clip is played back together with
FM3&4CLIP, the transition. At this point, you can also carry
FM5&6CLIP, out a transition (wipe or mix (dissolve))
FM7&8CLIP simultaneously together with the clip.
KF
(keyframe)
Press this button, turning it on, to enable
using the fader lever as a keyframe fader.
Name Description
AUTO
TRANS
(transition)
button
• Pressing this button carries out an auto
transition of the set transition rate
(duration). The transition starts immediately,
and the button lights amber.
• When the transition completes, the button
goes off.
CUT button Pressing this button carries out the transition
as a cut (i.e. instantaneously).
Name Description
Transition
indicator This comprises multiple LEDs, which show
the progress of the transition.
Fader lever
• Move this vertically to carry out a manual
transition.
• When the [KF] button or a transition type
selection button to which the KF button
function has been assigned is lit, you can
use this as a keyframe fader.
Transition
rate display
• This shows the “transition rate” (the time
from the beginning of a transition to its
completion) set for an auto transition, in
frames.
• You can set the transition rate using the
numeric keypad control block, Flexi Pad
control block, or menu.
Ch
a
p
te
r 2
M
e
n
u
s
and
Co
n
tr
o
l P
a
n
e
l
c
Transition execution section
This section is used to carry out a transition, and check the
signal status during the transition.
Transition indicator
Fader lever
d
Wipe direction selection buttons
For details, see “Wipe direction selection buttons” (page
39).
e
TRANS PVW (transition preview) button
When this button is lit, you can check in advance the video
changes during the transition, on the preview output from
the M/E or PGM/PST bank.
During the preview, you can use the fader lever, [AUTO
TRANS] button, and [CUT] button. One of the following
functions of this button can be selected in the Setup menu.
•
When the transition completes, the system returns to the
normal mode.
•
The transition preview mode is maintained while this
button is pressed.
•
Switching is made between the transition preview mode
and normal mode every time this button is pressed.
f
Key status display
For each of keys 1 to 4, the corresponding ON indicator
lights when the key is inserted. It also shows the priority (1
to 4) of each key.
g
PRIOR (priority) SET button
While this button is held down, you can set the key
priority.
The setting mode when this button is pressed depends on
whether or not the [KEY PRIOR] button is lit, as follows.
•
When the [KEY PRIOR] button is off, the current key
priority is set.
•
When the [KEY PRIOR] button is lit, the key priority
after the next transition is set.
Press the [KEY PRIOR] button as required, to switch
between these two modes.
In either mode, hold down the [PRIOR SET] button, and
press the button ([KEY1] to [KEY8]) corresponding to the
key you want to bring to the front.
Notes
The key priority establishes a separate priority order within
each of the groups of keys 1 to 4 and keys 5 to 8. You can
make any setting within the groups of keys 1 to 4 or keys
5 to 8, but not for combinations of keys from different
groups. For example, it is not possible to set a priority
sequence of keys 1, 5, and 2.