Sony MVS-8000X SystemMVS-7000X System, User Manual

Page: 145 / 706

USO
RESTRITO
Key Adjustments (Key Control Block)
145
Ch
a
p
te
r 4
K
e
y
s
a) In the “4H mode” and when [Fine Key] (page 135) is on, the setting value
range is 0 to 4.
To adjust the edge fill color
When [BDR] is selected, the [MORE] button lights amber.
Pressing the [MORE] button to turn it green then allows
you to adjust the edge fill color parameters with the knobs.
Knob Parameter Adjustment Setting values
1 Luminance Luminance 0 to 100
2 Saturation Saturation 0 to 100
3 Hue Hue 359 to 0
4 Density Density 0 to 100
Setting the drop border or shadow
parameters
When the [DROP BDR] or [SHDW] button is lit green, the
parameter settings differ between the “key drop OFF” and
“key drop ON” modes
(see page 125) as shown below.
You switch between these two modes by turning the [KEY
DROP] button on or off.
“Key drop OFF” mode
Knob Parameter Adjustment Setting values
1 Width Width 0 to 8
a)
2 Position Position 359 to 180
4 Density Density 0 to 100
a) In the “4H mode” and when [Fine Key] (page 135) is on, the setting value
range is 0 to 4.
“Key drop ON” mode
Knob Parameter Adjustment Setting values
1 Width Width
0 to 8
a)
2 Position Position 359 to 0
4 Density Density 0 to 100
a) In the “4H mode” and when [Fine Key] (page 135) is on, the setting value
range is 0 to 4.
To adjust the edge fill color
When [DROP BDR] or [SHDW] is selected, the [MORE]
button lights amber. Pressing the [MORE] button to turn it
green then allows you to adjust the edge fill color
parameters with the knobs.
Knob Parameter Adjustment Setting values
1 Luminance Luminance 0 to 100
2 Saturation Saturation 0 to 100
3 Hue Hue 359 to 0
4 Density Density 0 to 100
Setting the outline parameters
When the [OUTLINE] button is lit green, the parameter
settings depend on the key type and whether the separate
edge function is active. To activate the separate edge
function, press [Separate Edge], setting it on, in the Edge
menu for the key.
Separate edge off
Knob Parameter Adjustment Setting values
1 Width Outline width
0 to 8
a)
(0 to 100)
b)
4 Density Outline density 0 to 100
a) In the “4H mode” and when [Fine Key] (page 135) is on, the setting value
range is 0 to 4.
b) When a wipe pattern key or key wipe pattern key is selected as the key type
Separate edge on
The outline width settings can be made independently for
left, right, top, and bottom sides. The separate edge
function is only available when luminance key, linear key,
or chroma key is selected as the key type.
Knob Parameter Adjustment Setting values
1 Top Top edge width
0 to 8
a)
2 Left Left edge width 0 to 8
a)
3 Right Right edge width
0 to 8
a)
4 Bottom Bottom edge width 0 to 8
a)
a) In the “4H mode” and when [Fine Key] (page 135) is on, the setting value
range is 0 to 4.
When [Outline] is selected with separate edge on, the
[MORE] button lights amber. Pressing the [MORE] button
to turn it green then allows you to adjust the key fill density
parameter with a knob.
Knob Parameter Adjustment Setting values
4 Density Outline density 0 to 100
Setting the embossing parameters
When the [EMBOS] button is lit green, adjust the
following parameters.
Knob Parameter Setting values
1 Width 0 to 4
2 Position 359 to 0
4 Density 0 to 100
Selecting a normal edge
When all five edge type selection buttons are off, a normal
edge is selected. If one of the buttons is lit, press it, turning
it off.
Softening the edge
Press the [SOFT EDGE] button, turning it on. The button
lights green, and you can now adjust the softness with the
knob.