Sony DVW-250 Maintenance Manual Download Page 247

Page: 247 / 272

9-11

DVW-250/250P

9-4. Audio System Adjustment

Play back a 12 kHz, -20 VU portion (TIME;04 : 00 :

00 - 04 : 24 : 29) of the alignment tape.

Equipment

Audio Analyzer

Test point

AUDIO OUT CH-4 connector on

the connector panel

Adjustment point

RV801 (G-1 : B) /EQ-54

Specification

0.7 dBm (600

Ω

)

Perform STEP 1 again.

Eject the tape.

Setting after adjustment

Reset switches to the former positions.

9-4-6. CUE Bias Adjustment

Preparation

• Disconnect the cable from the AUDIO IN CH-4 connec-

tor/connector panel.

• CUE REC switch/connector panel

→

• MODE switch/connector panel

→

PB/EE

Adjustment procedure

Insert a blank tape and put into the REC mode.

Equipment

Audio noise meter

Test point

TP804 (G-1 : B) /EQ-54

GND

TP805 (G-1 : B) /EQ-54

Adjustment point

CV800 (G-2 : A or B) /EQ-54

Specification

1 mV rms

Equipment

Oscilloscope

Test point

TP803 (G-2 : B) /EQ-54

Specification

Check that the level is 1.8 Vp-p or

less.

Repeat steps 2 and 3 until the specifications (steps 2

and 3) are met.

1.8 Vp-p or less

EQ-54 Board B side

TP803

RV801 RV802

TP804

RV803

TP805

EQ-54 Board A side

CV800

Summary of Contents for DVW-250

















































































































































































































































































Search results

Summary of Contents for DVW-250

Reviews:

Related manuals for DVW-250

Brands by name

Popular brands

Sony DVW-250, Maintenance Manual

Search results

Summary of Contents for DVW-250

Reviews:

Related manuals for DVW-250

Brands by name

Popular brands