Sony DVW-250 Maintenance Manual Download Page 88

Page: 88 / 272

6-18

DVW-250/250P

6-4. Upper Drum Assembly Replacement

(4) Put the four screws (removed in step 4) in the

four holes on the board of the upper drum

assembly using a pair of tweezers.

(5) Using an L wrench thread the four screws

tentatively in the sequence shown in the

figure. Do not tighten them.

7. Upper drum eccentricity gauge

installation

(1) Clean the probe of the gauge with a cleaning

cloth moistened with cleaning fluid.

• If the prove were dirty, upper drum may

scratch during adjustment.

• If the prove were made of metal, it recom-

mends that the lubricated protective tape

puts on the prove to prevent from the

scratching.

(2) Attach the gauge shown in the figure and

adjust so that the probe is positioned between

the bottom two grooves of the five which

locate on the outside of the upper drum

assembly.

Take care not to touch the probe against the

video heads.

Screw

Tape

Tape (3mm width)

Probe

Upper drum eccentricity adjustment tool
(assembled)

Upper drum

Probe

2nd groove from bottom

1st groove from bottom

Summary of Contents for DVW-250

















































































































































































































































































Search results

Summary of Contents for DVW-250

Reviews:

Related manuals for DVW-250

Brands by name

Popular brands

Sony DVW-250, Maintenance Manual

Search results

Summary of Contents for DVW-250

Reviews:

Related manuals for DVW-250

Brands by name

Popular brands