Sony DVW-250 Maintenance Manual Download Page 142

Page: 142 / 272

6-72

DVW-250/250P

6-19. Battery Replacement

6-19. Battery Replacement

The set data in the setup menu is returned to the factory-setting value when the

battery is replaced. To maintain the set data, use the SAVE command in the ISR

menu.

Overviews

Opening the back side of chassis

Battery replacement

Closing the back side of chassis

Preparations

(1) Put the unit into the unthreading end mode.

(2) Turn off the power.

(3) Remove the bottom plate. (Refer to “1-5. Removal/Installation of Cabinet”.)

Removal

1. Opening the back side of chassis

(1) Disconnect the connectors CN209 and

CN210 on the VPR-12 board.

(2) Remove the DPR-62 board.

(Refer to Section 8-2-4.)

(3) Disconnect all the connectors on the SST-3

board.

(4) Open the SST-3 board.

Installation

2. Battery replacement

(1) Remove the fastener fixing the battery using

nippers.

(2) Desolder the battery terminals on the SST-3

board, and remove the battery.

(3) Solder a new battery to the SST-3 board.

(4) Fix the battery to the SST-3 board with a new

fastener.

Never protrude a knot from the outside of the

board.

Summary of Contents for DVW-250

















































































































































































































































































Search results

Summary of Contents for DVW-250

Reviews:

Brands by name

Popular brands

Sony DVW-250, Maintenance Manual

Search results

Summary of Contents for DVW-250

Reviews:

Brands by name

Popular brands