Sony DVW-250 Maintenance Manual Download Page 104

Page: 104 / 272

6-34

DVW-250/250P

6-9. Cue Brush Replacement

6-9. Cue Brush Replacement

Overviews

Cue brush removal

Cue brush installation

Operation check

Preparations

Put the unit in the unthreading end mode.

Turn off the power.

Remove the top panel. (Refer to “1-5. Removal/Installation of Cabinet”.)

When replacing, prepare a new stop washer (P/N 3-321-393-01).

Tool

• Stop washer fastening tool: J-6323-530-A

Removal

1. Cue brush removal

Remove the stop washer at the top of the cleaner

arm and the cue brush.

Installation

2. Cue brush installation

(1) Insert a new cue brush into the cleaner arm

shaft and put the hole at the bottom of the cue

brush securely in the hook of the cleaner arm.

(2) Attach the cue brush using a new stop washer

while holding the cue lever with fingers.

3. Operation check

Check that the cue brush moves and touches the

CUE/TC head surface for cleaning when the

manual eject gear is turned clockwise and coun-

terclockwise while it is pushed downward.

Stop washer

CUE lever

Claw

CUE/TC head block

CUE brush

Summary of Contents for DVW-250

















































































































































































































































































Search results

Summary of Contents for DVW-250

Reviews:

Brands by name

Popular brands

Sony DVW-250, Maintenance Manual

Search results

Summary of Contents for DVW-250

Reviews:

Brands by name

Popular brands