Sony DVW-250 Maintenance Manual Download Page 91

Page: 91 / 272

6-21

DVW-250/250P

6-5. Drum Assembly Replacement

6-5. Drum Assembly Replacement

Overviews

Replacement

Video head cleaner assembly removal

Drum assembly removal

Cleaning of contact surfaces

Drum assembly installation

Video head cleaner assembly installation

Cleaning of video heads and tape running surfaces

Adjustment after replacement

Video head cleaner assembly position adjustment

Tape path adjustment

Servo adjustment

Video adjustment

Caution

When replacing the drum assembly be careful not to damage the CTL head, CUE/

TC head, and peripheral tape guide.

Be careful not to break the video heads of the drum assembly.

Basic information

Apart from the periodic replacement time, the drum assembly needs to replace in the

following cases.

• If the drum assembly could not use because the tape running surface of the upper

or lower drum scratched.

• If a correct RF waveform did not obtain after the tracking adjustment due to wear-

out on the upper or lower drum.

• If the specification of the VTR such as jitter or noise did not meet due to the short

life of the bearing.

Preparations

Check that the unit is in the unthreading end mode.

Turn off the power.

Remove the top panel. (Refer to “1-5. Removal/Installation of Cabinet”.)

Remove the cassette compartment. (Refer to Section 1-6.)

Tools

• Torque screwdriver bit (for B2): J-6325-380-A

• Torque screwdriver (for 3 kg) : J-6325-400-A

• Cleaning cloth

: 3-184-527-01

• Cleaning fluid

: 9-919-573-01

Summary of Contents for DVW-250

















































































































































































































































































Search results

Summary of Contents for DVW-250

Reviews:

Brands by name

Popular brands

Sony DVW-250, Maintenance Manual

Search results

Summary of Contents for DVW-250

Reviews:

Brands by name

Popular brands