Sony DVW-250 Maintenance Manual Download Page 108

Page: 108 / 272

6-38

DVW-250/250P

Removal and installation

1. Tension regulator roller (S5)

replacement

(1) Turn the setscrew at the top of the tension

regulator roller counterclockwise by 180

degrees, then loosen.

Do not tighten or loosen the setscrew until

step (5) is completed after it is loosened. If

tighten or loosen, the adjustment after tape

guide roller replacement becomes difficult.

(2) Turn the upper flange counterclockwise and

remove it.

(3) Remove the tension regulator roller, and

remove two pieces of roller Cs simultaneous-

ly.

(4) Install the roller C, a new tension regulator

roller and another roller C sequentially in the

tape guide shaft.

(5) Turn the setscrew of the upper flange re-

moved in step (2) clockwise by 180 degrees.

(Turn same degrees in the opposite direction

in step (1).)

(6) Turn the upper flange clockwise as far as it

will go and attach it to the tape guide shaft.

6-11. Tension Regulator Roller Replacement

Tension regurator roller

Set screw

Tension regurator

Set screw

Upper flange

Roller C

Tension regulator roller

Roller C

Guide shaft

Summary of Contents for DVW-250

















































































































































































































































































Search results

Summary of Contents for DVW-250

Reviews:

Brands by name

Popular brands

Sony DVW-250, Maintenance Manual

Search results

Summary of Contents for DVW-250

Reviews:

Brands by name

Popular brands