Sony DVW-250 Maintenance Manual Download Page 122

Page: 122 / 272

6-52

DVW-250/250P

6-13. T Reel Brake Solenoid Replacement

17. Manual eject assembly position

adjustment

(1) Insert a screwdriver into the hole of the

manual eject gear and loosen the screw

shown in the figure.

(2) Put a wire clearance gauge of 0.3 mm in

diameter between the gear(black) and

threading motor gear as shown in the figure,

and push the manual eject gear toward the

motor gear.

(3) Tighten the screw through the hole of the

manual eject gear while maintaining the state

in step (2).

The position of the manual eject assembly is

then adjusted.

(4) Pull out the wire clearance gauge.

Adjustment after replacement

18. Tape path adjustment

(Refer to Section 7-1-1.)

Wire clearance gauge

Motor gear

Gear(black)

Motor gear

Position adjusting screw

Manual eject gear

Wire clearance gauge

Gear(black)

Summary of Contents for DVW-250

















































































































































































































































































Search results

Summary of Contents for DVW-250

Reviews:

Related manuals for DVW-250

Brands by name

Popular brands

Sony DVW-250, Maintenance Manual

Search results

Summary of Contents for DVW-250

Reviews:

Related manuals for DVW-250

Brands by name

Popular brands