Sony DVW-250 Maintenance Manual Download Page 96

Page: 96 / 272

6-26

DVW-250/250P

6-5. Drum Assembly Replacement

5. Video head cleaner assembly

installation

(1) Attach the video head cleaner assembly with

one screw.

Take care not to touch the video head cleaner

assembly against the drum assembly (espe-

cially the video heads).

(2) Connect the harness connector of the video

head cleaner solenoid to connector CN960 on

the MB-601 board.

6. Cleaning of video heads and tape

running surfaces

Clean the following area using a cleaning cloth

moistened with cleaning fluid.

• Video heads (Refer to “5-1. Cleaning”.)

• Tape running surface of the upper drum (Refer

to “5-1. Cleaning”.)

• Tape running surface and lead of the lower

drum (Refer to “5-1. Cleaning”.)

After cleaning, be sure to wipe the relevant area

using a dry cleaning cloth.

Adjustments after replacement

7. Video head cleaner assembly position

adjustment

(Refer to Section 6-14.)

8. Tape path adjustment

(Refer to Section 7-1-1.)

9. Servo system adjustment

(Refer to Section 9-3.)

10. RF system adjustment

(Refer to Section 9-5-1, and 9-5-4 to 9-5-13.)

Summary of Contents for DVW-250

















































































































































































































































































Search results

Summary of Contents for DVW-250

Reviews:

Related manuals for DVW-250

Brands by name

Popular brands

Sony DVW-250, Maintenance Manual

Search results

Summary of Contents for DVW-250

Reviews:

Related manuals for DVW-250

Brands by name

Popular brands