Sony DVW-250 Maintenance Manual Download Page 211

Page: 211 / 272

7-37

DVW-250/250P

7-2-15. Drum PG Phase Adjustment

Tools

• Alignment tape ZR2-1

8-960-073-11

• Alignment tape ZR2-1P

8-960-073-61

• Oscilloscope

• Regulated DC power supply

(AC-550/550CE or equivalent)

Setting

Turn the power off.

Remove the top panel.

(Refer to “1-5. Removal/Installation of Cabinet”.)

Set the DIP switches.

(Refer to “7-2-4. DIP switch Setting”.)

Remove the ornamental plate on the left side panel.

(Refer to “1-13. Tracking Adjustment”.)

Connect an oscilloscope.

CH-1: TP10/MB-601

CH-2: TP8/MB-601

Connect a regulated DC power supply to DC IN

connector on the connector panel.

Turn the power on.

Insert an alignment tape ZR2-1/1P.

On the setup menu, set AUTO TRACKING to OFF.

10. Turn the tracking control volume to the mechanical

center(click position).

7-2-15. Drum PG Phase Adjustment

Summary of Contents for DVW-250

















































































































































































































































































Search results

Summary of Contents for DVW-250

Reviews:

Related manuals for DVW-250

Brands by name

Popular brands

Sony DVW-250, Maintenance Manual

Search results

Summary of Contents for DVW-250

Reviews:

Related manuals for DVW-250

Brands by name

Popular brands