Sony DVW-250 Maintenance Manual Download Page 225

Page: 225 / 272

7-51

DVW-250/250P

7-3-1. Tension Regurator Adjustment

Adjusting table

7-3. Mechanical Alignment

7-3-1. Tension Regurator Adjustment

Tools

• FWD back tension mesuring cassette

:J-6323-890-A

• S-tension arm positioning pin

:J-7031-030-A

• Weight for S-tension adjustment(W76.7):J-7031-040-A

• Weight for S-tension (W44)

:J-7031-050-A

• S-TEN adjusting table

:J-7031-280-A

• End sensor positioning tool

:J-7031-450-A

• Digital volt meter

• Digital Betacam cassette BCT-D40

:Standard product

• Regurated DC power supply

(AC-550/550CE or euivalent)

Setting

Turn the power off.

Remove the top panel.(Refer to “1-5.Removal/

Installation of Cabinet” maintenance manual part1)

Set the S-TEN adjusting table on the horizontal board

so that the table leaves a fit space.

Open the battery lid on the left side panel.

Lay the DVW-250/250P on the S-TEN adjusting table

left side down.

Connect an digital volt meter.

prove(+) : “TP7” pin on the MB-601 board

prove(-) : “E1” ground pin on the MB-601 board

Connect a regurated DC power supply to DC IN

connector on the connector pannel.

Turn the power on.

Summary of Contents for DVW-250

















































































































































































































































































Search results

Summary of Contents for DVW-250

Reviews:

Related manuals for DVW-250

Brands by name

Popular brands

Sony DVW-250, Maintenance Manual

Search results

Summary of Contents for DVW-250

Reviews:

Related manuals for DVW-250

Brands by name

Popular brands