Sony DVW-250 Maintenance Manual Download Page 261

Page: 261 / 272

9-25

DVW-250/250P

9-7. Video Adjustment-2

9-7. Video System Adjustment-2

Preparation

• Put the unit into EE mode.

MODE switch/connector panel

→

PB/EE

Put the unit into STOP mode.

• CONFI switch/connector panel

→

OFF

• On the setup menu, set PAGE and ITEM as follows. (for

NTSC only)

PAGE

: <VIDEO 1> <SET UP LEVEL>

ITEM

: MASTER LEVEL

→

7.5%

ITEM

: INPUT LEVEL

→

MASTER

ITEM

: V BLK REMOTE CNT

→

OFF

ITEM

: OUTPUT LEVEL

→

MASTER

• On the setup menu, set PAGE and ITEM as follows.

PAGE

: <VIDEO 2>

ITEM

: VIDEO LEVEL

→

0.0%

PAGE

: <VIDEO 2>

ITEM

: SDI OUT

→

9-7-1. Pedestal Level Adjustment

Preparation

• Put the unit into EE mode.

• CAMERA/VIDEO/SDI input select switch/connector

panel

→

VIDEO

• VIDEO LEVEL knob/connector panel

→

Mechanical

center (Click position)

• Inputs the composite video signal to the VIDEO IN

connector on the connector panel.

Signal generator : 75 % Color bars

Adjustment procedure

Equipment

Oscilloscope

Test point

VIDEO OUT1 connector /

connector panel

Adjustment point

RV202 (F-1)/VPR-12

Specification

3 mV

VPR-12 Board A side

TP203

RV202

Summary of Contents for DVW-250

















































































































































































































































































Search results

Summary of Contents for DVW-250

Reviews:

Related manuals for DVW-250

Brands by name

Popular brands

Sony DVW-250, Maintenance Manual

Search results

Summary of Contents for DVW-250

Reviews:

Related manuals for DVW-250

Brands by name

Popular brands