manualshive.com logo in svg

Sony DVW-250, Maintenance Manual

Share
Download
Sony DVW-250 Maintenance Manual Download Page 78

6-8

DVW-250/250P

3.

Intermediate position between L and S cassette position:

It means that positions of two driving racks are the same place, and A portion of

the slide link parallels to the unit. (Refer to following figure.)

How to put the unit into the L cassette position, S cassette position and intermediate

position between L and S cassette positions:

Turn an idle gear as shown in the figure until the reel table assemblies shift to the

desired position and driving rack lock.

n

If a cassette tape is inserted, the reel tables can not be shifted.

Driving racks

SE-233 board

S reel table

T reel table

Slide link

A portion

Driving racks

S reel table

S cassette 
portion

L cassette 
portion

Idle gear

6-1. General Information for Mechanical Part Replacement

Summary of Contents for DVW-250

















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands