Sony DVW-250 Maintenance Manual Download Page 140

Page: 140 / 272

6-70

DVW-250/250P

6-18. Threading Motor Replacement

Installation

4. Threading motor replacement

(1) Remove the two screws and the threading

motor from the gear block assembly.

(2) Press the two new pinion gears in the shaft of

a new threading motor.

• Press a new pinion gear B (P/N 3-680-988-

01) to the shaft on the terminal side.

• Press a new pinion gear (P/N 3-679-748-

01) in the other side of the shaft so that the

tip of the shaft is the same as the surface of

the pinion gear.

(3) Attach the threading motor in the gear block

assembly using the two screws.

Threading motor

Screw

Gear block

Screw

Threading motor

Pinion gear

Pinion B

Wiring side

Be flush the pinion gear
with the motor shaft.

Summary of Contents for DVW-250

















































































































































































































































































Search results

Summary of Contents for DVW-250

Reviews:

Brands by name

Popular brands

Sony DVW-250, Maintenance Manual

Search results

Summary of Contents for DVW-250

Reviews:

Brands by name

Popular brands