Sony DVW-250 Maintenance Manual Download Page 123

Page: 123 / 272

6-53

DVW-250/250P

6-14. Video Head Cleaner Solenoid Replacement

6-14. Video Head Cleaner Solenoid Replacement

Overviews

Video head cleaner assembly removal

Cleaner solenoid replacement

Video head cleaner assembly installation

Video head cleaner assembly position adjustment

Operation check

Note

When replacing, be careful not to damage the CTL head, drum assembly, and

peripheral tape guides. Especially, be careful not to damage the video heads of the

drum assembly during replacement.

Preparations

Put the unit in the unthreading end mode.

Turn off the power.

Remove the top panel. (Refer to “1-5. Removal/Installation of Cabinet”.)

Removal

1. Video head cleaner assembly removal

Remove the video head cleaner assembly. (Refer to Section 6-8.)

Installation

2. Cleaner solenoid replacement

(1) Remove the two screws at the back of the

video head cleaner assembly, and remove the

solenoid.

(2) Remove the rubber ring shown in figure, and

install it to new solenoid.

(3) Attach a new solenoid to the cleaner base in

the direction shown in the figure while

putting the groove of the iron core of the

solenoid in the boss of the solenoid lever, and

tighten it with the two screws.

Screws

Cleaner base

Solenoid

Rubber ring

Summary of Contents for DVW-250

















































































































































































































































































Search results

Summary of Contents for DVW-250

Reviews:

Related manuals for DVW-250

Brands by name

Popular brands

Sony DVW-250, Maintenance Manual

Search results

Summary of Contents for DVW-250

Reviews:

Related manuals for DVW-250

Brands by name

Popular brands