Sony DVW-250 Maintenance Manual Download Page 99

Page: 99 / 272

6-29

DVW-250/250P

6-7. Pinch Roller Arm Assembly Replacement

6-7. Pinch Roller Arm Assembly Replacement

Overviews

Replacement

Pinch roller arm assembly removal

Shaft cleaning

pinch roller arm assembly installation

Operation check

Pinch roller cleaning

Adjustment after replacement

Tape running check

Note

If the pinch roller worn-out, replace the pinch roller arm assembly.

Preparations

Put the unit in the unthreading end mode.

Turn off the power.

Remove the top panel. (Refer to “1-5. Removal/Installation of Cabinet”.)

Reference

The pinch roller arm assembly can replace with the cassette compartment attaches to

the unit.

When replacing, prepare a new stop washer (P/N 3-726-829-01).

Tools

• Stop washer fastening tool: J-6323-530-A

• Cleaning piece

: 2-034-697-00

• Cleaning fluid

: 9-919-573-01

Summary of Contents for DVW-250

















































































































































































































































































Search results

Summary of Contents for DVW-250

Reviews:

Related manuals for DVW-250

Brands by name

Popular brands

Sony DVW-250, Maintenance Manual

Search results

Summary of Contents for DVW-250

Reviews:

Related manuals for DVW-250

Brands by name

Popular brands