Sony DVW-250 Maintenance Manual Download Page 178

Page: 178 / 272

7-4

DVW-250/250P

7-1-4. Preparations

Before adjustments in this section, perform as follows.

(1) Turn the power off.

(2) Remove the top panel. (Refer to “1-5. Removal/Installation of Cabinet”.)

(3) Clean the following places using a cleaning piece moistened with cleaning fluid.

(Refer to “5-1. Cleaning”.)

• Video head

• Tape running surface of upper drum

• Tape running surface and lead of the lower drum

• Stationary heads

• Tape cleaner

• All tape guides

• Capstan shaft

• Pinch roller

7-1-5. Tools

Use the following tools in this section.

• Tape guide adjustment screwdriver

J-6321-500-A

• Tape guide driver spare bit

J-6322-420-3

• Inspection mirror (Small oval type)

J-6080-840-A

• Cleaning piece

2-034-697-00

• Cleaning fluid

9-919-573-01

• Torque screwdriver (for 3 kg)

J-6325-400-A

• Torque screwdriver bit (for M2)

J-6325-380-A

• Torque screwdriver hex. bit (across 1.27 mm)

J-7031-460-A

• Alignment tape ZR2-1

8-960-073-11

• Alignment tape ZR2-1P

8-960-073-61

Contents

The CTL head height adjustment can use at any position of this alignment tape.

TIME

min.:sec.

CTL TRACK

CUE TRACK

VIDEO/AUDIO

TRACK

00 : 00

(7 : 3 PULSE)

CTL

1 kHz, 0 VU

4MHz

(A CH only)

15 : 00

CTL

12 kHz, 0 VU

A,C CH-4MHz
B,D CH-8MHz

20 : 00

25 : 00

27 : 00

CTL

12 kHz, 0 VU

16MHz

(ALL CH)

CTL

50% FLAT FIELD

(ALL CH)

• Video tracking adustment
• CTL head position adustment
• CUE head height adustment
• CUE/TC head position adustment

• CUE/TC head azimuth adustment
• CUE/TC head head-to-tape contact adustment

USE

• PG adustment

7-1-4. Preparations
7-1-5. Tools

Summary of Contents for DVW-250

















































































































































































































































































Search results

Summary of Contents for DVW-250

Reviews:

Brands by name

Popular brands

Sony DVW-250, Maintenance Manual

Search results

Summary of Contents for DVW-250

Reviews:

Brands by name

Popular brands