manualshive.com logo in svg

Sony DVW-250, Maintenance Manual

Share
Download
Sony DVW-250 Maintenance Manual Download Page 146

6-76

DVW-250/250P

6-21. S Reel Motor Assembly Replacement

Overviews

Replacement

Connector disconnection

S reel motor assy removal

S reel motor assy replacement

Open the back side of the chassis.

S reel motor assy installation

Driving belt installation

Close the back side of the chassis.

Connector connection

Adjustment after replacement

Servo system adjustment

Preparation

1.

Put the unit into the unthreading end state.

2.

Turn the power off.

3.

Remove the upper panel. (Refer to section 1-5.)

4.

Remove the cassette compartment. (Refer to section 1-6.)

Tools

• Torque screwdriver bit (for M2) : J-6325-380-A

• Torque screwdriver (for 3 kg)

: J-6325-400-A

• Thickness gauge

: 9-911-053-00

Removal

1. Connector disconnection

Disconnect the two connectors (CN951 (S reel

motor) and CN952 (S brake solenoid)) on the

MB-601 board.

6-21. S Reel Motor Assembly Replacement

CN951

CN952

MB-601 board

Summary of Contents for DVW-250

















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands