Sony DVW-250 Maintenance Manual Download Page 35

Page: 35 / 272

1-25

DVW-250/250P

1-12. Cleaning when the Heads are

Clogged

How to clean the video head when the heads are clogged,

refer to “5-1-2. Cleaning of Tape Running Surface of

Upper Drum and Video Heads”.

If it recommended to clean the video heads periodically to

avoid head clogging.

1-13. Tracking/Audio Meter Adjustment

1-13-1. Tracking Adjustment

When perform the tracking adjustment, perform the

following steps.

Set the setup menu as follows. (Refer to Section 3-1.)

PAGE:<TRACKING>

ITEM:AUTO TR

→

OFF

Remove the screw and open the L SUB cover.

Put the driver into the hole for tracking adjustment,

and adjust the tracking.

1-13-2. Audio Meter Contrast Adjustment

When perform the audio meter contrast adjustment,

perform the following steps.

Remove the screw and open the L SUB cover.

Put the driver into the hole for LCD contrast, and

adjust the LCD contrast.

1-14. Optional Accessories

1-14-1. Optional Accessories

Soft carrying case

: BKDW-250

Battery

: BP-L60

BP-90A

AC Power adaptor

: AC-550(for UC)

AC-550CE(for SY)

Battery Charger

: BC-L100(for UC)

BC-L100CE(for SY)

BC-410(for UC)

BC-410CE(for SY)

Video cassette tape

: BCT-D series

Remote controller

: BVR-3

RF modulator

: REU-89UCA(for UC)

RFU-89EAU(for SY)

1-12. Cleaning when the Heads are Clogged

1-13. Tracking/Audio Meter Adjustment

1-14. Optional Accessories

Driver

L SUB cover

Hole for tracking adjustment

Hole for LCD contrast

Summary of Contents for DVW-250

















































































































































































































































































Search results

Summary of Contents for DVW-250

Reviews:

Related manuals for DVW-250

Brands by name

Popular brands

Sony DVW-250, Maintenance Manual

Search results

Summary of Contents for DVW-250

Reviews:

Related manuals for DVW-250

Brands by name

Popular brands