manualshive.com logo in svg

Sony DVW-250, Maintenance Manual

Share
Download
Sony DVW-250 Maintenance Manual Download Page 213

7-39

DVW-250/250P

7-2-16. CTL Head Position Check

Note

• The CTL head position adjustment is closely related to

the CUE/TC head position adjustment. After performing

the CTL head position adjustment, be sure to perform

the CUE/TC head position check.

Tools

•  Alignment tape ZR2-1

8-960-073-11

•  Alignment tape ZR2-1P

8-960-073-61

•  Torque screwdriver bit (for M2)

J-6325-380-A

•  Torque screwdriver (for 3 kg)

J-6325-400-A

•  Oscilloscope

•  Regulated DC power supply

(AC-550/550CE or equivalent)

Setting

1.

Turn the power off.

2.

Remove the top panel.

(Refer to “1-5. Removal/Installation of Cabinet”.)

3.

Remove the battery case.

(Refer to “1-5. Removal/Installation of Cabinet”.)

4.

Remove the ornamental plate on the left side panel.

(Refer to “1-13. Tracking Adjustment”.)

5.

Set all four switches of DIP switches S1 and S2 on the

UDR-9 board which attaches to the upper drum to ON.

6.

Set the switch S700-1 on the EQ-54 board to ON.

7.

Connect a regulated DC power supply to DC IN

connector on the connector panel.

8.

Turn the power on.

9.

On the setup menu, set AUTO TRACKING to OFF.

10. Insert an alignment tape ZR2-1/1P.

11. Set the color frame switch on the connector panel to

ON.

Checks

1. Oscilloscope setting (1)

Connect an oscilloscope

CH-1 : TP10/MB-601 (REC A)

TRIG : TP8/MB-601 (CF)

2. Playback the alignment tape

 Play back the alignment tape ZR2-1/1P (from 00:00 to

15:00).

7-2-16. CTL Head Position Check

Summary of Contents for DVW-250

















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands