Sony DVW-250 Maintenance Manual Download Page 255

Page: 255 / 272

9-19

DVW-250/250P

9-5-6. ADC Sampling Phase Adjustment

Use the identical probes of the oscilloscope.

Adjustment procedure

Insert an alignment tape (ZR5-1/P) and put the unit

into the PB mode.

Oscilloscope settings

• AC mode

• 20 MHz BW Limit:OFF

• Set the GND levels of CH-1 and CH-2 are at the

center of the oscilloscope.

A/Ech Adjustment

Test point

TP104 (A-3:B) /EQ-54

TRIG

TP105 (A-3:B) /EQ-54

Adjustment point

CV100 (A-2:B) /EQ-54

Specification

A = 0

2 ns

9-5. RF System Adjustment

EQ-54 Board B side

TP405

TP305

TP205

TP105

RV104

TP204

TP304

TP404

CV100

CV200

CV300

CV400

RV100

RV200

RV300

RV400

RV304

RV404

RV204

TP104

Adjust the B/F, C/G, D/H channels in the same way.

Test point

TRIG

Adjustment point

B/Fch

TP204 (C-3:B)

TP205 (C-3:B)

CV200 (B-2:B)

C/Gch TP304 (D-3:B)

TP305 (D-3:B)

CV300 (D-2:B)

D/Hch TP404 (F-3:B)

TP405 (E-3:B)

CV400 (E-2:B)

Eject the tape.

TP12

TP13

TP11

MB-601 Board A side

Summary of Contents for DVW-250

















































































































































































































































































Search results

Summary of Contents for DVW-250

Reviews:

Brands by name

Popular brands

Sony DVW-250, Maintenance Manual

Search results

Summary of Contents for DVW-250

Reviews:

Brands by name

Popular brands