Sony DVW-250 Maintenance Manual Download Page 237

Page: 237 / 272

9-1

DVW-250/250P

9-1. General Information for Electrical Adjustment

9-1-1. Notes for Adjustment

Before adjustment, turn the power on and warm up the unit for about 10 munites.

Be sure to put the unit into EE mode according to the following procedures, if neccessary.

MODE switch/connector panel

→

PB/EE

Put the unit into STOP mode.

9-1-2. Equipment/Fixtures

Equipment

Model

AC Adapter or Battery

Sony AC-550 (for UC) /550CE (for SY) or equivalent

Oscilloscope

Tektronix 2465B or equivalent

Analog Composite Signal Generator

Tektronix 1410 (for NTSC) /1411 (for PAL) or equivalent

Waveform Monitor/Vectorscope

Tektronix 1750 (for NTSC) /1751 (for PAL) or equivalent

Digital Voltmeter

Advantest TR6845 or equivalent

Audio Level Meter

Hewlett Packard HP 3400A or equivalent

Audio Analyzer

Tektronix AA501A (OP.02) or equivalent

Audio Oscillator

Tektronix SG-5010 or equivalent

Audio Noise Meter

READER LMV-189AR or equivalent

Audio Distortion Meter

Tectronix AA5010 or equivalent

Monitor

Sony BVM-1410 or equivalent

Frequency Counter

Advantest TR5821AK or equivalent

Alignment Tape ZR5-1 (for NTSC)

Part No. : 8-960-073-01

Alignment Tape ZR5-1P (for PAL)

Part No. : 8-960-073-51

Alignment Tape ZR2-1 (for NTSC)

Part No. : 8-960-073-11

Alignment Tape ZR2-1P (for PAL)

Part No. : 8-960-073-61

Blank Tape

Digital Betacam Cassette Tape

Extension Harness

Part No. : J-6421-430-A (for VIDEO)

Part No. : J-6421-440-A (for AUDIO)

Extension Board

Part No. : J-6421-330-A (for DIF-31)

Note:

1: “Blank Tape” indicates a cassette tape on which no video/audio signals are recorded.

2: Connect between the following connectors when open the video boards assembly.

CN209 (K-2) /VPR-12 — (12 pins) — CN457 (A-2) /CC-66
CN210 (K-3) /VPR-12 — (8 pins) — CN456 (B-2) /CC-66

3: Connect between the following connectors when open the video boards assembly.

CN206 (H-2) /DPR-62 — (10 pins) — CN555 (D-3) /ADA-44
CN207 (H-2) /DPR-62 — (12 pins) — CN556 (B-3) /ADA-44
CN208 (H-2) /DPR-62 — (6 pins) — CN559 (D-3) /ADA-44

Section 9

Electrical Alignment

Summary of Contents for DVW-250

















































































































































































































































































Search results

Summary of Contents for DVW-250

Reviews:

Related manuals for DVW-250

Brands by name

Popular brands

Sony DVW-250, Maintenance Manual

Search results

Summary of Contents for DVW-250

Reviews:

Related manuals for DVW-250

Brands by name

Popular brands