Sony DVW-250 Maintenance Manual Download Page 174

Page: 174 / 272

6-104

DVW-250/250P

20. Drum assembly installation

(1) Clean the contact surfaces of the drum

assembly and chassis using a cleaning cloth

moistened with cleaning fluid.

• When holding the drum assembly, be sure

to hold the no video heads portion.

• Take care not to touch the drum assembly

against the stationary heads.

(2) Connect the three connectors (CN1, CN2 and

CN3) to the lower board of the drum.

(3) Put the two positioning pins of the chassis to

the holes of the drum assembly.

(4) Move the drum assembly a little and check that

the drum assembly fit in the positioning pins.

(5) Tighten the three screws.

21. Connection the brush assembly

connector

Connect the connector to the brush assembly

board.

22. Unthread guide plate installation

Attach the unthread guide plate using the two

screws.

23. SE-233 board installation

Attach the SE-233 board using two screws.

24. Cleaning of the heads and the tape

running surface

Cleaning the following areas using a cleaning

cloth moistened with cleaning fluid.

• Video heads (Refer to section 5-1-2)

• Tape running surface of the upper drum (Refer

to section 5-1-2)

• Tape running surface and lead of the lower

drum (Refer to section 5-1-3)

After cleaning, be sure to wipe the relevant areas

using a dry cleaning cloth.

Adjustment after this replacement

25. Tape path adjustment

(Refer to section 7-1-1)

26. Tension regulator adjustment

(Refer to section 7-3-1)

6-25. Replacement of the Component Parts of the Threading Link Block

Summary of Contents for DVW-250

















































































































































































































































































Search results

Summary of Contents for DVW-250

Reviews:

Brands by name

Popular brands

Sony DVW-250, Maintenance Manual

Search results

Summary of Contents for DVW-250

Reviews:

Brands by name

Popular brands