Sony DVW-250 Maintenance Manual Download Page 133

Page: 133 / 272

6-63

DVW-250/250P

6-17. CUE/TC Head Replacement

Preparations

Put the unit into the unthreading end mode.

Turn off the power.

Remove the top panel. (Refer to “1-5. Removal/Installation of Cabinet”.)

Remove the cassette compartment. (Refer to Section 1-6.)

Use a harness clamper to arrange the harness of the CUE/TC head assembly and fix

them securely. Prepare a new band (3-906-254-01) before replacement.

Tools

• Torque screwdriver bit (for M1.4): J-6325-110-A

• Torque screwdriver bit (for M2) : J-6325-380-A

• Torque screwdriver (for 3 kg)

: J-6325-400-A

• Cleaning cloth

: 3-184-527-01

• Cleaning fluid

: 9-919-573-01

Removal

1. Pinch solenoid assembly removal

Remove the pinch solenoid assembly. (Refer to

Section 6-10.)

2. Open the EQ-54 board

Open the EQ-54 board. (Refer to Section 8-6.)

3. Disconnection of connectors

(1) Disconnect connector CN304 (cue head) on

the EQ-54 board.

(2) Disconnect the two connectors CN947 (TC

head) and CN949 (cue erase head) on the

MB-601 board.

(3) Disconnect the two ground plugs CN931 and

CN932 on the MB-601 board.

CN304

(EQ-54 board)

CN932 CN931

CN949

CN947

(Right part of MB-601 board)

Summary of Contents for DVW-250

















































































































































































































































































Search results

Summary of Contents for DVW-250

Reviews:

Brands by name

Popular brands

Sony DVW-250, Maintenance Manual

Search results

Summary of Contents for DVW-250

Reviews:

Brands by name

Popular brands