Sony DVW-250 Maintenance Manual Download Page 244

Page: 244 / 272

9-8

DVW-250/250P

9-4. Audio System Adjustment

9-4-1. PB Level/Distortion Adjustment

Preparation

• SL1-SL8/ADA-44

→

OPEN (Head room

20 dB)

• CH-3/4 OUT switch/connector panel

→

LINE

• Put the unit into the EE mode.

MODE switch/connector panel

→

PB/EE

Put the unit into STOP mode.

• On the setup menu, set PAGE and ITEM as follows.

PAGE

<AUDIO>

ITEM

INPUT 1/2

→

ANA

ITEM

INPUT 3/4

→

ANA

ITEM

EMPHASIS

→

OFF

• On the DIAG menu, set PAGE and ITEM as follows.

PAGE

ITEM

AUDIO TEST

→

1 (1 kHz, 0 dB)

Adjustment procedure

CH-1 PB Level Adjustment

Equipment

Audio level meter

Test point

AUDIO OUT CH-1 connector

Adjustment point

RV205 (C-2 : B) /ADA-44

Specification

+4.0

0.1 dBm (600

Ω

)

CH-1 Distortion Adjustment

Equipment

Audio distortion meter

Test point

AUDIO OUT CH-1 connector

Adjustment point

RV201 (A-3 : B) /ADA-44

Specification

Minimum (0.03% or less)

Adjust the distortion for channnel-2 through 4 in the

same way.

Test point

Adjustment point

PB level

Distortion

CH-2

AUDIO OUT CH-2

RV206 (D-2 : B)

RV202 (A-3 : B)

CH-3

AUDIO OUT CH-3

RV207 (E-2 : B)

RV203 (A-2 : B)

CH-4

AUDIO OUT CH-4

RV208 (E-2 : B)

RV204 (A-2 : B)

Setting after adjustment

Reset switches and menu to the former positions.

9-4-2. INPUT Level Adjustment

Preparation

• SL1-SL8/ADA-44

→

OPEN (Head room

20dB)

• Put the unit into the EE mode.

MODE switch/connector panel

→

PB/EE

Put the unit into STOP mode.

• CH-3/4 OUT switch/connector panel

→

LINE

• CAMERA/LINE switches (CH-1 through CH-4) /

connector panel

→

LINE

• -60/-20/+4 dB switches (CH-1 through CH-4) /connector

panel

→

+4 dB

• AUDIO REC LEVEL ON/OFF/PRESET switches

(CH-1 through CH-4) /connector panel

→

PRESET

• AUDIO PB LEVEL knob (CH-1 through CH-4)

/front panel

→

fully clockwise (MAX)

• On the setup menu, set PAGE and ITEM as follows.

PAGE

<AUDIO>

ITEM

INPUT 1/2

→

ANA

ITEM

INPUT 3/4

→

ANA

ITEM

EMPHASIS

→

OFF

Adjustment procedure

CH-1 INPUT Level Adjustment

Inputs 1 kHz +4 dBu signal to the AUDIO IN CH-1

connector on the connector panel.

Equipment

Audio level meter

Test point

AUDIO OUT CH-1 connector

Adjustment point

RV1 (L-3 : B) /ADA-44

Specification

+10.0

0.1 dBm (600

Ω

)

Adjust the distortion for channnel-2 through 4 in the

same way.

Test point

Adjustment point

CH-2

AUDIO OUT CH-2

RV2 (L-2 : B)

CH-3

AUDIO OUT CH-3

RV3 (L-2 : B)

CH-4

AUDIO OUT CH-4

RV4 (L-2 : B)

Setting after adjustment

• AUDIO PB LEVEL knob (CH-1 through CH-4) /

front panel

→

reference level position (+4 dBm)

• Reset switches and menu to the former positions.

9-4. Audio System Adjustment

Summary of Contents for DVW-250

















































































































































































































































































Search results

Summary of Contents for DVW-250

Reviews:

Related manuals for DVW-250

Brands by name

Popular brands

Sony DVW-250, Maintenance Manual

Search results

Summary of Contents for DVW-250

Reviews:

Related manuals for DVW-250

Brands by name

Popular brands