Sony DVW-250 Maintenance Manual Download Page 161

Page: 161 / 272

6-91

DVW-250/250P

6-24. T Link and T Drawing Arm Assembly Replacement

Overviews

Replacement

Mode setting

T link and T drawing arm assmbly removal

T link or T drawing arm assmbly replacement

T link and T drawing arm assmbly installation

Operation confirmation

Cleaning

Adjustment after replacement

Tape path adjustment

Reference:

This section describes the replacement procedure of the T link and T drawing arm

assy. The two parts are much the same in replacement procedure. Replace the parts

to be handled according to the procedure below.

Preparation

Put the unit into the unthreading end state.

Turn the power off.

Remove the upper panel. (Refer to section 1-5.)

Remove the cassette compartment. (Refer to section 1-6.)

Stop washer and E-ring are used to install the T link and T drawing arm assy.

Prepare a new stop washer (3-669-465-01) and a new E-ring (7-624-102-01) during

replacement.

Tool

• Stop washer insertion tool

: J-6323-530-A

• Cleaning cloth

: 3-184-527-01

• Cleaning liquid

: 9-919-573-01

• Oil

: 7-661-018-18

6-24. T Link and T Drawing Arm Assembly Replacement

Summary of Contents for DVW-250

















































































































































































































































































Search results

Summary of Contents for DVW-250

Reviews:

Brands by name

Popular brands

Sony DVW-250, Maintenance Manual

Search results

Summary of Contents for DVW-250

Reviews:

Brands by name

Popular brands