Sony DVW-250 Maintenance Manual Download Page 84

Page: 84 / 272

6-14

DVW-250/250P

6-4. Upper Drum Assembly Replacement

6-4. Upper Drum Assembly Replacement

Overviews

Replacement

Brush cover removal

Brush assembly removal

Unsoldering the leads of slip ring assembly

Upper drum assembly removal

Cleaning of contact surfaces

Upper drum assembly installation

Upper drum eccentricity gauge installation

Upper drum eccentricity adjustment

Upper drum eccentricity gauge removal

Solder the leads of slip ring assembly

Brush assembly installation

Brush cover installation

Cleaning of video heads and tape running surfaces

Adjustment after replacement

Tape path adjustment

Servo system adjustment

RF system adjustment

Note

If the rotary heads worn out or broke, replace the upper drum assembly. The head

chip cannot replace.

Basic information

Apart from the periodic replacement time, the upper drum assembly needs to replace

in the following case.

• If a correct RF waveform cannot be obtained after the tracking adjustment is

performed

Preparations

Check that the unit is in the unthreading end mode.

Turn off the power.

Remove the top panel. (Refer to “1-5. Removal/Installation of Cabinet”.)

Remove the cassette compartment. (Refer to Section 1-6.)

Summary of Contents for DVW-250

















































































































































































































































































Search results

Summary of Contents for DVW-250

Reviews:

Brands by name

Popular brands

Sony DVW-250, Maintenance Manual

Search results

Summary of Contents for DVW-250

Reviews:

Brands by name

Popular brands