Sony DVW-250 Maintenance Manual Download Page 103

Page: 103 / 272

6-33

DVW-250/250P

6-8. Video Head Cleaning Roller Replacement

4. Video head cleaner assembly position

adjustment

(1) Move the video head cleaner assembly in the

direction of the arrow and tighten the one

screw which temporarily fixed in step 3 so

that the clearance between the pin and

bracket meets the specification when the iron

core of the solenoid is pushed with fingers to

energized state.

(2) Check that the specification is met again.

5. Operation check

Push the iron core of the video head cleaner

assembly solenoid with fingers to energized state.

Check that the AHC roller assembly touches the

drum (video head portion) shown in the figure.

Video head cleaner
assembly

Screw

Space A

Space B

Space B = 0.3 ±0.2 mm

AHC roller assembly

Plunger

Solenoid

Summary of Contents for DVW-250

















































































































































































































































































Search results

Summary of Contents for DVW-250

Reviews:

Brands by name

Popular brands

Sony DVW-250, Maintenance Manual

Search results

Summary of Contents for DVW-250

Reviews:

Brands by name

Popular brands