Siemens SIMOTICS S-1FL6 Operating Instructions Manual Download Page 355 | Manualshive

Page: 355 / 432

background image

Parameters

10.2 Parameter list

SINAMICS V90, SIMOTICS S-1FL6
Operating Instructions, 04/2019, A5E36037884-007

353

Par. No.

Name

Min

Max

Factory

Setting

Unit Data

type

Effective

Can be

changed

p2546 *

LR dynamic following

error monitoring tolerance

0

214748364

7

3000/62

9146

LU U32

IM

T, U

Description: Sets the tolerance for the dynamic following error monitoring.
If the dynamic following error (r2563) exceeds the selected tolerance, then an appropriate fault is output.
For a motor with an incremental encoder, the default value is 3000. For a motor with an absolute encoder, the

default value is 629146.
Value = 0: The dynamic following error monitoring is deactivated.
Dependency: Refer to r2563, F07452
Note: The tolerance bandwidth is intended to prevent the dynamic following error monitoring incorrectly re-

sponding due to operational control sequences (e.g. during load surges).

p2571

IPos maximum velocity

1

40000000

30000 100

0

LU/

min

U32

IM

T, U

Description: Sets the maximum velocity for the "basic positioner" function (IPos).
Note: The maximum velocity is active in all of the operating modes of the basic positioner.
The maximum velocity for the basic positioner should be aligned with the maximum speed/velocity of the

speed/velocity controller.

p2572 **

IPos maximum accelera-

tion

1

2000000

Motor

de-

pendent

100

0

LU/s

²

U32

IM

T

Description: Sets the maximum acceleration for the "basic positioner" function (IPos).
Note: The maximum acceleration appears to exhibit jumps (without jerk).
"Traversing blocks" operating mode:
The programmed acceleration override acts on the maximum acceleration.
"Direct setpoint input/MDI" mode:
The acceleration override is effective.
"Jog" and "search for reference" modes:
No acceleration override is active. The axis starts with the maximum acceleration.

p2573 **

IPos maximum decelera-

tion

1

2000000

Motor

de-

pendent

100

0

LU/s

²

U32

IM

T

Description: Sets the maximum deceleration for the "basic positioner" function (IPos).
Note: The maximum deceleration appears to exhibit jumps (without jerk).
"Traversing blocks" operating mode:
The programmed deceleration override acts on the maximum deceleration.
"Direct setpoint input/MDI" mode:
The deceleration override is effective.
"Jog" and "search for reference" modes:
No deceleration override is effective. The axis brakes with the maximum deceleration.

«
...
353
354
355
356
357
...
»

Summary of Contents for SIMOTICS S-1FL6

















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SIMOTICS S-1FL6

Brand: Valor Pages: 97

Brand: CG Pages: 45

Brand: ACM Pages: 37

Brand: MTD Pages: 40

PneuTorque PTS-52-500

Brand: norbar Pages: 30

Brand: Plettenberg Pages: 26

Brand: BMW Pages: 41

Throttling Governor Kerosene Stationary Engines

Brand: Worthington Pages: 33

Brand: cemp Pages: 18

Brand: Baumr-AG Pages: 25

Enduro RR 350 2015

Brand: Beta Pages: 158

Brand: YS Pages: 2

Brand: Detroit Diesel Pages: 42

Brand: Yanmar Pages: 316

Brand: Seva-tec Pages: 20

Brand: DANA Pages: 4

Brand: DANA Pages: 3

Brand: DANA Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands