Siemens SIMOTICS S-1FL6 Operating Instructions Manual Download Page 362

Page: 362 / 432

Parameters

10.2 Parameter list

SINAMICS V90, SIMOTICS S-1FL6

360

Operating Instructions, 04/2019, A5E36037884-007

Par. No.

Name

Min

Max

Factory

Setting

Unit Data

type

Effective

Can be

changed

p29016

PTI: Pulse input filter

[0] 0

I16

Description: Select filter for PTI input to get better EMC performance, 0 for low frequency PTI input, 1 for high

frequency PTI input.

p29019

RS485 monitor time

1999999

ms Float

T, U

Description: Sets the monitoring time to monitor the process data received via the RS485 bus interface. If no

process data is received within this time, then an appropriate message is output.
Note: If p29019 = 0, monitoring is deactivated.

p29020[0..

.1]

Tuning: Dynamic factor

U16

T, U

Description: The dynamic factor of auto tuning. 35 dynamic factors in total are available.
Index:

•

[0]: Dynamic factor for one

-button auto tuning

•

[1]: Dynamic factor for real

-time auto tuning

p29021

Tuning: Mode selection

I16

Description: Selection of a tuning mode.

•

0: Disabled

•

1: One-button auto tuning

•

3: Real-time auto tuning

•

5: Disable with default controller parameters

p29022

Tuning: Ratio of total

inertia moment to motor

inertia moment

1.00

10000.00

1.00

Float

T, U

Description: Ratio of total inertia moment to servo motor inertia moment.

p29023

Tuning: One-button auto

tuning configuration

0xffff

0x0007 -

U16

Description: One-button auto tuning configuration.

•

Bit 0: The speed controller gain is determined and set using a noise signal.

•

Bit 1: Possible required current setpoint filters are determined and set using a noise signal. As a conse-

quence, a higher dynamic performance can be achieved in the speed control loop.

•

Bit 2: The inertia moment ratio (p29022) can be measured after this function is running. If not set, the iner-

tia moment ratio must be set manually with p29022.

•

Bit 7: With this bit set, multi-axes are adapted to the dynamic response set in p29028. This is necessary

for interpolating axes. The time in p29028 should be set according to the axis with the lowest dynamic re-

sponse.

Summary of Contents for SIMOTICS S-1FL6

















































































































































































































































































































































































































































Search results

Summary of Contents for SIMOTICS S-1FL6

Reviews:

Related manuals for SIMOTICS S-1FL6

Brands by name

Popular brands

Siemens SIMOTICS S-1FL6, Operating Instructions Manual

Search results

Summary of Contents for SIMOTICS S-1FL6

Reviews:

Related manuals for SIMOTICS S-1FL6

Brands by name

Popular brands