Panasonic VB-44210G User Manual Download Page 323

Page: 323 / 394

Section 700-Operation

Appendix A. EX 1.0 Feature Update

DBS-2.3/9.2-700

DBS Manual - Revised April 2000

Page A-33

Figure A-13.SMDR Format for CPC-EX

Setting Modified for SMDR

Values have been redefined for the SMDR Start Timer. The following table shows the
enhanced values.

Note:

These values apply to CPC-EX only.

Programming

See

Section 400 - Programming (Appendix C)

for more detailed

programming information.

0 1 2 3 4 5 6 7

012345678901234567890123456789012345678901234567890123456789012345678901234567

1 2 3 4 5 6 7 8 9

T MM/DD HH:MM:SS HH:MM.SS NNN DDDDDDDDDDDDDDDDDDDDDDDDDDDD AAAAAAAAAA VVVVV NN

1=Call type

S=Inbound DISA

s=Outbound DISA

I=Incoming

O=Outgoing

T=Transfer (See Note 1)

N=DNIS

D=DID

W=CO outgoing to Network

w=CO incoming from network

t=Network Transfer

r=ISDN incoming call

R=ISDN outgoing call

2=Date

MM=month

DD=day

3=Call start time

HH=hours

MM=minutes

SS=seconds

4=Call duration

HH=hours

MM=minutes

SS=seconds

5=Extension number (or network trunk)

10-69, 100-699=extensions

CO number=DISA

n01-n04=virtual port 1 to 4

#01-#64=network trunk number

6=Dialed digits, Caller ID or ANI

DD=digits 0-9 or symbols * or

(See Note 2)

7=Account code

A=0-9999999999

8=Verified account code or walking

COS code

V0000-V9999=verified account codes

W0000-W9999=walking COS codes

9=Trunk Number

NN=number (01-64)

Notes:

1. Transferred calls include direct and group call pickups and conference calls.

If a station call is transferred to an outside number, an SMDR record is

also created for the station that is transferred.

2. The * symbol appears as a greater-than sign (>) on the SMDR printout; the # symbol

appears as a less-than sign (<). Centrex and PBX codes, as well as LCR access codes, do

not appear as dialed digits. If the Caller ID Feature is installed and enabled,

“Private” appears with calls that have restricted Caller ID display and “Out of Area”

with long distance calls that do not provide Caller ID information.

Summary of Contents for VB-44210G











































































































































































































































































































































































































Search results

Summary of Contents for VB-44210G

Reviews:

Related manuals for VB-44210G

Brands by name

Popular brands

Panasonic VB-44210G, User Manual

Search results

Summary of Contents for VB-44210G

Reviews:

Related manuals for VB-44210G

Brands by name

Popular brands