Panasonic VB-44210G User Manual Download | Manualshive

Page: 54 / 394

background image

Chapter 3. System Features

Section 700 - Operation

Page 3-8

DBS Manual - Revised April 2000

DBS-2.3/9.2-700

Related Programming

• FF1 (System): Automatic Day Mode Start Time

• FF1 (System): Automatic Night Mode Start Time

Considerations

• If both auto modes are set, the starting times must differ by at least one

hour.

• When one auto mode is turned on, the mode cannot be reset by the

NIGHT

key until 3 minutes after the auto mode is activated. (When both auto
modes are set, the

NIGHT

key cannot be used.)

• If a

NIGHT

key is not assigned, the access code #52 can be used instead.

Auto Day Mode

(CPC-B Version 7.0 or higher and CPC-A II Version 7.0 and higher)

Description

Auto Day Mode allows the DBS to go into day mode automatically.

The DBS can also be programmed to go into night mode automatically (see
“Night Service,” page 3-37).

If only one of the auto modes is turned on, the

DAY/NIGHT1/NIGHT2

toggle key or the

DAY

,

NIGHT1

, or

NIGHT2

is used to turn off the auto

mode. For instance, if

NIGHT1

mode has been activated automatically, the

attendant must press the

DAY/NIGHT1/NIGHT2

toggle key or the

DAY

key

to go into day mode. (Note: You must wait at least 3 minutes after the
automatic mode is activated before manually changing the mode. Otherwise
the system will immediately revert back to the automatic mode.)

If only one of the auto modes is turned on, the

DAY/NIGHT1/NIGHT2

toggle key or the

DAY

,

NIGHT1

, or

NIGHT2

key can also be used to go into

an auto mode before the scheduled time. If auto day and both auto night
modes are turned on, the manual mode keys

can

be used.

Related Programming

• FF1 (System): Auto Day Mode Start Timer

• FF1 (System): Auto Night1 Mode Start Timer

«
...
52
53
54
55
56
...
»

Summary of Contents for VB-44210G











































































































































































































































































































































































































Reviews:

No comments

Related manuals for VB-44210G

Brand: NEC Pages: 12

Brand: Panasonic Pages: 8

Brand: Aastra Pages: 28

Brand: HAGENUK Pages: 76

Brand: Samsung Pages: 79

Brand: Samsung Pages: 88

Brand: Samsung Pages: 215

Brand: Samsung Pages: 155

Brand: Aastra Pages: 2

Brand: Radio Shack Pages: 12

Brand: Uniden Pages: 12

SureCross DX99 FlexPower DX99N9X2S0N0R4X0A0

Brand: Banner Pages: 7

Brand: Qwest Pages: 46

Brand: AT&T Pages: 51

Brand: Telongo Pages: 6

Titan Illuminated Crossing Telephone

Brand: GAI-Tronics Pages: 14

Brand: Kirstein Pages: 4

Brand: Zazen Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands