Panasonic VB-44210G User Manual Download Page 293 | Manualshive

Page: 293 / 394

background image

Section 700-Operation

Appendix A. EX 1.0 Feature Update

DBS-2.3/9.2-700

DBS Manual - Revised April 2000

Page A-3

FF-Key Programming

Because T1 Networking adds the capability of 4-digit extension numbering, you can now
program up to 8 digits (not 6) into an FF-key.

Speed Dial Enhancements

CPC-EX supports up to 500 System Speed Dial (SSD) numbers. CPC-EX also allows SSD
codes to be chained, or “linked”, to another SSD number, and either PSD or SSD codes to be
chained to a PSD number.

Additional Serial Port

The CPC-EX card contains an on-board serial port (Serial Port 2) which can be used for Bus
Monitor/Maintenance. This allows remote maintenance to be accomplished without
disconnecting SMDR cabling.

T1 Networking Capability

Up to 4 DBS’s can now be connected together via T1 interface to form a DBS phone
network. The DBS’s can be located in the same building, in separate buildings in a campus-
type environment, or at remote locations in separate states. Networked DBS’s use 4-digit
extensions, with the first digit of the extension number identifying the DBS site.

Each site requires its own DBS cabinet with a CPC-EX card and a T1 card. Programming
addresses are included in CPC-EX software for setting up the T1 Network.

(see the T1

Networking Reference Manual for complete instructions.)

Modification to Toll Restriction Service

The program address for TRS Operator Access (FF7 1# 18#) has been modified to allow an
extension to dial “0+NXX” phone numbers, even if “0-only” dialing is denied.

Maximum Time Priority Route Tables

CPC-EX allows a maximum of 8 Time Priority Route Tables (not 15) to be used during LCR
programming. Since few systems use more than 3 Time Priority Route Tables, this change
will allow the saved memory space to be used for future enhancements.

«
...
291
292
293
294
295
...
»

Summary of Contents for VB-44210G











































































































































































































































































































































































































Reviews:

No comments

Related manuals for VB-44210G

Brand: E-MetroTel Pages: 4

Brand: NEC Pages: 42

Brand: NEC Pages: 8

Brand: NEC Pages: 220

Brand: NEC Pages: 2

OpenScape CP600

Brand: Unify Pages: 32

OpenScape CP700

Brand: Unify Pages: 24

OpenScape CP200

Brand: Unify Pages: 2

OpenScape CP600

Brand: Unify Pages: 2

OpenScape Desk Phone IP 35G

Brand: Unify Pages: 130

Brand: Unify Pages: 2

Brand: Unifat Technology Pages: 6

FINISH-OUT MC111M

Brand: M&S Systems Pages: 2

Brand: Panasonic Pages: 67

Brand: Opus Technologies Pages: 24

SpectraLink 8002 Series

Brand: Polycom Pages: 72

Brand: Jabra Pages: 7

Brand: Uniden Pages: 41

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands