Panasonic VB-44210G User Manual Download Page 56

Page: 56 / 394

Chapter 3. System Features

Section 700 - Operation

Page 3-10

DBS Manual - Revised April 2000

DBS-2.3/9.2-700

4. Enter the four-digit auto set relocation code assigned to extension 200.

5. Replace the handset.

• All programmed extension features and TRS settings from 200 are

transferred to 300.

• Extension 300 are placed out of service.

To Reactivate Extension 300:

1. Unplug the extension cable from 300.

2. Reconnect the cable.

Extension 300 assumes all extension features, TRS, and LCR settings that
were initially assigned to 200.

Related Programming

• FF3 (Extension): Auto Set Relocation Code

Considerations

• The following types of data can be transferred using this feature:

- TRS type settings

- Ring settings (trunk line, remote ringing, day/night, DID)

- FF key data

- Extension numbers and names

- System call forward settings

- All settings and data defined by programming.

• Settings may not be transferred between extensions of different types. In

other words, an SLT and a KTEL cannot exchange program settings.

• Attendant 1 is excluded from this feature.

Summary of Contents for VB-44210G











































































































































































































































































































































































































Search results

Summary of Contents for VB-44210G

Reviews:

Related manuals for VB-44210G

Brands by name

Popular brands

Panasonic VB-44210G, User Manual

Search results

Summary of Contents for VB-44210G

Reviews:

Related manuals for VB-44210G

Brands by name

Popular brands