Panasonic VB-44210G User Manual Download Page 227

Page: 227 / 394

Section 700 - Operation

Chapter 5. DSLT Features

DBS-2.3/9.2-700

DBS Manual - Revised April 2000

5-9

Operation

To activate Call Forwarding:

1. Lift the handset or press

ON/OFF

The phone issues intercom dial tone.

2. Dial

“72.”

3. Dial the appropriate call forwarding code.

Note:

Beginning with CPC-AII and CPC-B Version 7.0, all forwarding

types (All Calls, No Answer, Busy, Busy/No Answer) allow call
forwarding outside eliminating the need for Call Forwarding--External.

4. If you are forwarding to an extension, enter the extension number. If you

are forwarding to an outside number, press

AUTO

plus the appropriate

speed dial number.

Note:

Outside numbers used for call forwarding must already be

programmed into speed dialing. (See page 5-35 for instructions.)

5. Replace the handset or press

ON/OFF

To cancel Call Forwarding

1. Lift the handset or press

ON/OFF

2. Dial

“72.”

3. Replace the handset or press

ON/OFF

Related Programming

• FF1 (System): Call Forward No Answer Timer

Call Forward
Type

Code

All 0

Busy/no answer

Busy

Outside

No answer

Summary of Contents for VB-44210G











































































































































































































































































































































































































Search results

Summary of Contents for VB-44210G

Reviews:

Related manuals for VB-44210G

Brands by name

Popular brands

Panasonic VB-44210G, User Manual

Search results

Summary of Contents for VB-44210G

Reviews:

Related manuals for VB-44210G

Brands by name

Popular brands