Panasonic VB-44210G User Manual Download Page 324

Page: 324 / 394

Appendix A. EX 1.0 Feature Update

Section 700-Operation

Page A-34

DBS Manual - Revised April 2000

DBS-2.3/9.2-700

Related Programming

• FF1 (System): SMDR Print

• FF1 (System): Parity Check

• FF1 (System): Odd/Even Parity

• FF1 (System): Baud Rate

• FF1 (System): Stop Bit Length

• FF1 (System): Data Length

• FF1 (System): Serial Port Flow Control (X On/ X Off)

• FF1 (System): SMDR Display Start Timer for CO Calls

• FF1 (System): SMDR Printing Mode 1: Outbound, Inbound, Network

• FF1 (System): SMDR Printing Mode 2: Long Distance and Local Calls

• FF1 (System): SMDR Printing Mode 3: Header Title

• FF3 (Extension) Station Message Detail Recorder (SMDR) Report

Hardware Requirements

• A printer or external call accounting system is required to receive SMDR

data.

Considerations

• Unlike other CPC circuit cards, the CPC-EX supports two serial ports.

Serial Port 1 is labeled

CN4

and is located on the backplane. Serial Port 2

is labeled

CN5

and is located on the front of the CPC-EX card. Serial Port

2 requires a special interface cable.

• Be sure to select the correct port to output SMDR data. From the

Attendant’s phone:

dial

#90

to set Serial Port 1 (the backplane port) to output Bus

Monitor/Maintenance and Serial Port 2 to no output.

- dial

#92

to set Serial Port 1 to output SMDR and Serial Port 2

to output Bus Monitor/Maintenance data.

- dial

#93

to set Serial Port 1 to output SMDR data and Serial

Port 2 to no output.

Summary of Contents for VB-44210G











































































































































































































































































































































































































Search results

Summary of Contents for VB-44210G

Reviews:

Related manuals for VB-44210G

Brands by name

Popular brands

Panasonic VB-44210G, User Manual

Search results

Summary of Contents for VB-44210G

Reviews:

Related manuals for VB-44210G

Brands by name

Popular brands