Panasonic VB-44210G User Manual Download Page 204 | Manualshive

Page: 204 / 394

background image

Chapter 4. Key Telephone Features

Section 700 - Operation

4-88

DBS Manual - Revised April 2000

DBS-2.3/9.2-700

• The line LED lights green.

• “CO TALK #XX” (where “XX” is the line) appears on the display.

2. Press

the

AUTO

key.

3. Press

“*.”

The dialed number appears on the display.

4. Complete the call and replace the handset.

The line LED changes from green to red and then goes off.

Considerations

• Any previously saved number is erased when a new number is saved.

• The Saved Number Redial feature can store a number up to sixteen digits

long.

• Up to five Speed Dialing codes can be stored and redialed.

Speed Dialing

(All Versions)

Personal Speed Dialing

Description

Extension users can store frequently called numbers using the Personal Speed
Dial feature. Up to 10 Personal Speed Dial numbers can be stored at each
extension.

With all versions prior to Version 7.0, the Personal Speed Dial bins are
numbered 90 to 99. With CPC-AII and CPC-B Version 7.0 and higher, the
Personal Speed Dial bins are numbered 900 to 909.

Users can also enter names of up to sixteen characters for each of the Speed
Dial numbers. This allows Personal Speed Dial numbers to be confirmed by
name rather than by number.

Extension users can program their own personal speed dial numbers using
One-Touch keys, or they can be programmed from a key phone.

«
...
202
203
204
205
206
...
»

Summary of Contents for VB-44210G











































































































































































































































































































































































































Reviews:

No comments

Related manuals for VB-44210G

Brand: Bang & Olufsen Pages: 2

Brand: Bang & Olufsen Pages: 20

Brand: Bang & Olufsen Pages: 24

BeoSound Ouverture

Brand: Bang & Olufsen Pages: 44

Brand: Talkswitch Pages: 3

Brand: TAG Heuer Pages: 8

Brand: Panasonic Pages: 72

Brand: Watts Pages: 12

Brand: Magnavox Pages: 78

Magnavox FW 55C

Brand: Magnavox Pages: 80

Brand: GE Pages: 48

Brand: Samson Pages: 45

Brand: Barnstead Thermolyne Corporation Pages: 32

Brand: Uniden Pages: 36

Brand: KAPSCH Pages: 78

Brand: Easydive Pages: 2

Brand: Daewoo International Pages: 26

Brand: salmson Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands