Panasonic VB-44210G User Manual Download Page 162 | Manualshive

Page: 162 / 394

background image

Chapter 4. Key Telephone Features

Section 700 - Operation

4-46

DBS Manual - Revised April 2000

DBS-2.3/9.2-700

Related Programming

• FF1 (System): Extension Class of Service Setting (CPC-AII and CPC-B

Version 4.0 or higher)

• FF3 (Extension): Extension Class of Service Assignment (CPC-AII and

CPC-B Version 4.0 or higher)

Considerations

• Callback Queuing will ring an extension in DND.

• A Private Line will ring an extension in DND.

• In CPC-A and CPC-B Versions prior to 5.0, DND and Absence Messages

cancel Call Forwarding.

Beginning with Version 5.0, calls to an extension with DND or Absence
Message turned on are treated differently, depending on whether they are
trunk or intercom calls. Intercom calls receive busy tone; trunk calls are
routed to the extension defined in permanent call forwarding.

The following types of incoming trunk calls will follow permanent call
forward settings:

- Direct trunk calls (including DID/DNIS)

- Transferred trunk calls.

• With CPC-A and CPC-B Version 1, DND is not available for Attendant

Phones. Beginning with CPC-B Version 2.0, Attendant Phones can
activate DND.

• The Attendant can activate or cancel this feature on an extension using FF

key LEDs on a DSS console.

• The DND feature cannot be activated from an extension selected to receive

call forwarding.

«
...
160
161
162
163
164
...
»

Summary of Contents for VB-44210G











































































































































































































































































































































































































Reviews:

No comments

Related manuals for VB-44210G

Brand: RAKINDA Pages: 20

Cordless Telephone

Brand: Radio Shack Pages: 12

Brand: Panasonic Pages: 72

Brand: Sonos Pages: 15

Brand: Clas Ohlson Pages: 2

Brand: Roadstar Pages: 80

efector190 DTE810

Brand: IFM Electronic Pages: 38

Linx 700-0120-501

Brand: ooma Pages: 10

Brand: BT Pages: 53

Brand: Walker Ameriphone Pages: 39

Brand: Radio Shack Pages: 25

Brand: SPX Pages: 36

Brand: Tala Pages: 4

Brand: VTech Pages: 2

Brand: Memorex Pages: 24

Brand: GE Pages: 36

Brand: GE Pages: 2

Brand: GE Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands