Panasonic VB-44210G User Manual Download Page 172 | Manualshive

Page: 172 / 394

background image

Chapter 4. Key Telephone Features

Section 700 - Operation

4-56

DBS Manual - Revised April 2000

DBS-2.3/9.2-700

Hot Dial Pad

Description

The dial pad on digital key phones can be designated as “hot” on an
extension-by-extension basis.

The Hot Dial Pad allows the user to initiate a call without going offhook.
Extensions with the Hot Dial Pad enabled can initiate calls by pressing any of
the numeric keys (0-9). The “*” and “#” keys are not hot.

The Dial Pad can be hot under these conditions:

• When the extension is idle

• When the extension is holding a call

• When the extension is receiving a page.

The Dial Pad cannot be hot under these conditions:

• When a call is ringing at the extension (intercom or CO)

• When the extension is on a call.

Related Programming

• FF3 (Extension Programming): Hot Dial Pad

Considerations

Paging:

The Hot Dial Pad cannot be used to initiate a page.

Intercom Calling

(All Versions)

Descriptions

The DBS provides two methods of intercom calling: voice calling and tone
calling.

Voice Calling.

With voice calling, intercom calls are connected

immediately, without a ringing tone.

«
...
170
171
172
173
174
...
»

Summary of Contents for VB-44210G











































































































































































































































































































































































































Reviews:

No comments

Related manuals for VB-44210G

Brand: DAB Pages: 8

Brand: Panasonic Pages: 252

KX-TH112 - Cordless Phone - Operation

Brand: Panasonic Pages: 10

Brand: Subpac Pages: 15

Brand: Raymarine Pages: 18

Dead Level Series

Brand: Watts Pages: 24

Box Design BT Box S2

Brand: Pro-Ject Audio Systems Pages: 6

Power Wheel Model 145

Brand: Auburn Gear Pages: 4

Brand: GAI-Tronics Pages: 16

Brand: T-Mobile Pages: 191

Brand: Oricom Pages: 25

Brand: Panasonic Pages: 84

EASA-PHONE KX-T30820

Brand: Panasonic Pages: 6

Brand: IPRO Pages: 12

Brand: CAME-TV Pages: 7

Brand: SoundRyder Audio Pages: 20

Brand: Aristel Pages: 67

Brand: Asus Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands