Panasonic VB-44210G User Manual Download Page 265 | Manualshive

Page: 265 / 394

background image

Section 700 - Operation

Chapter 6. SLT Features

DBS-2.3/9.2-700

DBS Manual - Revised April 2000

6-9

Considerations

• With CPC-A and CPC-B Versions prior to 2.0, calls cannot be forwarded

to an extension that already has call forwarding activated. In other words,
phone “A” could only forward to phone “B” if phone “B” was not
forwarded.

Beginning with CPC-B Version 2.0, calls can be forwarded to extensions
that have call forwarding activated. For example, phone “A” can be
forwarded to phone “B,” even if phone “B” is forwarded to voice mail.

• Calls can be forwarded to extensions that have call forwarding activated.

For example, phone “A” can be forwarded to phone “B,” even if phone
“B” is forwarded to voice mail.

• With CPC-AII and CPC-B 4.07 and later, extensions receiving forwarded

trunk calls display “CFWD NNN XXXXXX,” where “NNN” = the
extension that forwarded the call and “XXXXXX” = the trunk name or
number.

• In CPC-A and CPC-B Versions prior to 5.0, DND and Absence Messages

cancel Call Forwarding.

Beginning with CPC-B Version 5.0, calls to an extension with DND or
Absence Message turned on are treated differently, depending on whether
they are trunk or intercom calls. Intercom calls receive busy tone; trunk
calls are routed to the extension defined in permanent call forwarding.

The following types of incoming trunk calls follow permanent call forward
settings:

- Direct trunk calls (including DID/DNIS)

- Transferred trunk calls.

• Voice calls do not forward when Call Forwarding--No Answer is used.

• Extensions for which Call Forwarding-External has been set cannot:

- Be in the middle of an outside call when the feature is activated.

- Have a toll restriction setting that prohibits outside calls.

• Calls can be forwarded to a third-party voice mail with the “Call Forward

ID Code” described on page 3-13.

• Beginning with CPC-AII and CPC-B Version 7.0, all call types can be

forwarded outside using speed dials. However, if Least Cost Routing is
activated, dial “9” trunks cannot be used. Select another trunk group
instead (81-86).

«
...
263
264
265
266
267
...
»

Summary of Contents for VB-44210G











































































































































































































































































































































































































Reviews:

No comments

Related manuals for VB-44210G

Brand: Zenith Pages: 14

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 280

KXTVS100 - VOICE MAIL SYSTEM

Brand: Panasonic Pages: 91

Brand: Panasonic Pages: 872

Easa-Phone VA-208

Brand: Panasonic Pages: 45

Easa-Phone VA-208

Brand: Panasonic Pages: 45

Brand: Panasonic Pages: 128

Brand: Panasonic Pages: 408

Brand: 3Com Pages: 84

SuperStack 3 NBX

Brand: 3Com Pages: 496

Brand: 3CX Pages: 15

Brand: ICMA Pages: 2

Brand: Yealink Pages: 2

Brand: Dreamzon Pages: 80

SureCross DX99 FlexPower DX99N9X2S0N0R4X0A0

Brand: Banner Pages: 7

Brand: Nady Systems Pages: 8

Brand: Grandstream Networks Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands