manualshive.com logo in svg

Panasonic VB-44210G, User Manual

The Panasonic VB-44210G User Manual is essential for maximizing the potential of your phone system. This comprehensive manual provides step-by-step instructions and troubleshooting tips, ensuring a seamless user experience. Download it for free from manualshive.com and unleash the full capabilities of your Panasonic VB-44210G.

Share
Download
background image

Chapter 4. Key Telephone Features

Section 700 - Operation

 

4-50

DBS Manual - Revised April 2000

DBS-2.3/9.2-700

“ENTER FWD EXT#” appears on the display.

6. Press 

the 

AUTO

 key.

7.  Enter the Speed Dial code (System Speed dial 00-89 or Personal Speed 

dial 90-99 or 900-909).

Note: 

The speed dial code must include the 

CONF

 key (to indicate a 

trunk call), the appropriate trunk access code, and the outside number.

8. Press 

the 

HOLD

 key.

Calls will now be forwarded according to the forwarding type selected. 

To assign Call Forwarding to a Hunt Group pilot number or an 
extension number to an FF key:

1. Press 

the 

ON/OFF

 key.

2. Press 

the 

PROG

 key.

3.  Press the FF key to be programmed.

“Enter Code” appears on the display.

4. Enter 

“72.”

5.  Enter the Call Forwarding code (0, 1, 2, or 4).

6.  Enter the Hunt Group pilot number or an extension number.

7. Press 

the 

HOLD

 key.

To erase a code stored in an FF key:

Note: FF keys assigned as CO lines cannot be cleared using the following 
procedure. CO line keys can only be cleared through system programming

.

1. Press 

the 

ON/OFF

 key.

2. Press 

the 

PROG

 key.

3.  Press the FF key to be programmed.

“Enter Code” appears on the display.

4. Press 

the 

HOLD

 key.

“Code Cleared” appears.

Summary of Contents for VB-44210G











































































































































































































































































































































































































Reviews:

No comments

Related manuals for VB-44210G

BellSouth GH9407 Manual preview
GH9407
Brand: BellSouth Pages: 34
Linksys CIT310 - iPhone Cordless Phone Quick Installation preview
CIT310 - iPhone Cordless Phone
Brand: Linksys Pages: 2
BT HUDSON 1500 User Manual preview
HUDSON 1500
Brand: BT Pages: 2
jWIN JX-CD3003d Owner'S Manual preview
JX-CD3003d
Brand: jWIN Pages: 13
Scott I-WXH 80 Instruction Manual preview
I-WXH 80
Brand: Scott Pages: 13
VTech vt1122 User Manual preview
vt1122
Brand: VTech Pages: 2
Brähler Systems CMic Slim UTM Quick Manual preview
CMic Slim UTM
Brand: Brähler Systems Pages: 6
BellSouth MH9003 Owner'S Manual Installation And Operating Instructions preview
MH9003
Brand: BellSouth Pages: 33
Neon NTFPSMSFD11NT User Manual preview
NTFPSMSFD11NT
Brand: Neon Pages: 44
Inter-Tel Axxess 8500 User Manual preview
Axxess 8500
Brand: Inter-Tel Pages: 108
RCA RS2022 User Manual preview
RS2022
Brand: RCA Pages: 14
Emerson NR101TT Owner'S Manual preview
NR101TT
Brand: Emerson Pages: 16
Emerson Research iS133 Owner'S Manual preview
Research iS133
Brand: Emerson Pages: 2
Emerson PD6511 Owner'S Manual preview
PD6511
Brand: Emerson Pages: 8
Emerson MS9923TT Owner'S Manual preview
MS9923TT
Brand: Emerson Pages: 28
Emerson MS9933TT Owner'S Manual preview
MS9933TT
Brand: Emerson Pages: 36
Emerson MS9920 Owner'S Manual preview
MS9920
Brand: Emerson Pages: 14
Emerson RS1008 Owner'S Manual preview
RS1008
Brand: Emerson Pages: 31

Brands by name

Popular brands

Load more brands