Panasonic VB-44210G User Manual Download | Manualshive

Page: 203 / 394

background image

Section 700 - Operation

Chapter 4. Key Telephone Features

DBS-2.3/9.2-700

DBS Manual - Revised April 2000

4-87

Ringing Line Preference

(All Versions)

Description

Ringing Line Preference enables an extension to answer an incoming CO call,
hold recall, or transfer call by simply picking up the handset or pressing

ON/OFF

.

Related Programming

• FF3 (Extensions): Auto Pickup (Ringing Line Pickup)

Saved Number Redial

(All Versions)

Description

You can save a previously dialed number for later redialing. Unlike the Last
Number Redial feature, the Saved Number Redial feature allows you to redial
the stored number even if it was not the last number dialed.

Saved Number Redial works for outside numbers, but not for extension
numbers.

Operation

To save a number:

1. Press

the

AUTO

key twice before replacing the handset.

2. Press

“*.”

“Dial Stored” will appear on the display and the number will be saved.

3. Replace the handset.

To redial a saved number:

1. Press an unlit line key.

• The phone issues outside dial tone.

«
...
201
202
203
204
205
...
»

Summary of Contents for VB-44210G











































































































































































































































































































































































































Reviews:

No comments

Related manuals for VB-44210G

Brand: NEC Pages: 4

Brand: LENCO Pages: 27

Brand: Vanderbilt Pages: 10

Brand: Vicon Pages: 16

Brand: Jumbo Pages: 4

Infinite Station

Brand: Vodavi Pages: 38

Brand: Uniden Pages: 28

DECTsys-2200 pabx

Brand: Dectsys Pages: 35

Brand: Grundfos Pages: 21

Diamond Products GTXR+

Brand: HydraMaster Pages: 49

ProfiDAT compact

Brand: Conductrix Wampfler Pages: 32

Brand: Flying Voice Pages: 64

Brand: Yealink Pages: 56

Brand: BELGACOM Pages: 33

Brand: Valcom Pages: 1

JBL QUANTUM Stream Talk

Brand: Harman Pages: 15

Brand: Uniden Pages: 8

Brand: Bang & Olufsen Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands