Panasonic VB-44210G User Manual Download Page 101 | Manualshive

Page: 101 / 394

background image

Section 700 - Operation

Chapter 3. System Features

DBS-2.3/9.2-700

DBS Manual - Revised April 2000

Page 3-55

- 1 T1 Trunk Card (VB-43561

- 1 T1 MDF Card (VB-43562)

- 1 Sync Card (VB-43563).

In addition, one T1 Cable (VB-43564) is required to install a T1 in a double
cabinet if the T1 card is located in the slave cabinet.

To install two T1s in a double cabinet, you must have 2 T1 Trunk Cards and
2 T1 MDF Cards.

• The installer must provide a Channel Service Unit (CSU) that complies

with FCC Part 15 and Part 68. The CSU is installed between the DBS and
the public network. The CSU provides alarm, diagnostic, and monitoring
functions, as well as network protection.

Considerations

•

Fractional T1

can be used when fewer than 24 T1 trunks are needed.

Fractional T1 allows you to use only a portion of the 24 channels provided
on the T1 card.

• Though each T1 Interface provides 24 trunk channels, T1 trunks do not

increase the overall trunk capacity of the DBS. Each T1 channel subtracts
from the total number of analog trunks that can be installed. Furthermore,
the number of analog trunks that can be used may be decremented in
quantities of 1 or 8.

For instance, if you are installing a T1 in a DBS 96 and you only want to
use 12 T1 channels, the logical number of analog trunks that would be
available is 20 (32 - 12 = 20).

With CPC-B 5.00 and later, the number of analog trunks available are
decremented in quantities of 1. With CPC-B earlier than 5.00, the number
of analog trunks must be decremented in quantities of 8; the actual number
of analog trunks that can be used is 16:

(32 total trunks - 16 (two 8-trunk increments) = 16.)

• The current version of the T1 supports voice communications only. Data

can be transmitted only if it reaches the T1 in analog form. Examples of
analog data that can be transmitted over the T1 include fax transmissions
and PC files that have been converted into analog form using a modem.

«
...
99
100
101
102
103
...
»

Summary of Contents for VB-44210G











































































































































































































































































































































































































Reviews:

No comments

Related manuals for VB-44210G

Brand: Panasonic Pages: 268

Brand: iDance Pages: 10

Brand: Panasonic Pages: 5

Brand: Panasonic Pages: 4

Brand: Panasonic Pages: 24

Brand: Panasonic Pages: 42

Brand: Panasonic Pages: 135

Brand: Panasonic Pages: 23

Brand: PNI Pages: 2

Brand: Bayrol Pages: 56

Brand: RAM Pages: 22

Brand: Nortel Pages: 56

Brand: Karel Pages: 80

Brand: deconta Pages: 12

Brand: Daewoo Pages: 27

Brand: Topcom Pages: 28

Brand: GAI-Tronics Pages: 8

Brand: Teufel Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands