Panasonic VB-44210G User Manual Download Page 209 | Manualshive

Page: 209 / 394

background image

Section 700 - Operation

Chapter 4. Key Telephone Features

DBS-2.3/9.2-700

DBS Manual - Revised April 2000

4-93

2. Press

the

CONF

key.

“C” appears in the display.

3. Press

AUTO

.

4. Press a System Speed Dial key.

The programmed data appears on the display.

5. Press

the

ON/OFF

key.

• The

ON/OFF

LED goes off.

• The date and time appear on the display.

Related Programming

• FF1 (System): Speed Dial Mode Setting (CPC-AII and CPC-B Version 7.0

and higher)

• FF1 (System): Override Toll Restriction With SSD Numbers

• FF10 (Speed Dialing): System Speed Dialing

Considerations

• If numbers do not appear on the display when you use System Speed Dial

codes (00-89 or 000-199), your extension is not programmed to display
that data.

• The system can be programmed to allow System Speed Dial Numbers to

override toll restrictions.

• You can make outside calls using this feature, even if your extension is

assigned toll restriction type 2-6.

• Speed Dial code cannot be checked while Station Lockout is activated.

• With CPC-AII and CPC-B Version 7.0 and higher, if the Speed Dial is

used to forward to an outside number and Least Cost Routing is enabled,
the Speed Dial cannot use Trunk Access “9.” Use trunk access 81-86
instead.

«
...
207
208
209
210
211
...
»

Summary of Contents for VB-44210G











































































































































































































































































































































































































Reviews:

No comments

Related manuals for VB-44210G

Brand: N-Com Pages: 2

Brand: Talkswitch Pages: 30

Brand: STARPLUS Pages: 294

Brand: TANDBERG Pages: 12

Brand: Naked Pages: 12

Brand: Tablee Pages: 4

Brand: urmet domus Pages: 52

Brand: GAI-Tronics Pages: 5

Brand: Jensen Pages: 20

Brand: Tentel Pages: 10

Brand: Aastra Pages: 17

SPH200D - Cordless Phone / VoIP

Brand: NETGEAR Pages: 10

Brand: X4-TECH Pages: 2

Brand: Panasonic Pages: 24

Brand: AEI Pages: 6

Audio 2000's AMW6304U

Brand: H & F Technologies Pages: 6

Brand: GE Pages: 96

Brand: Curtis Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands