Panasonic VB-44210G User Manual Download Page 355 | Manualshive

Page: 355 / 394

background image

DBS-2.3/9.2-700

DBS Manual - Revised April 2000

Page E-1

Appendix E: CPC-EX 2.0 Updates

The following enhancements are included with CPC EX Version 2.0:

• CPC-EX Version 2.0 adds support for the PanaVOICE Digital Voice Mail

system.

All installation and programming procedures for the PanaVOICE Digital
Voice Mail system are covered in the documentation supplied with the
PanaVOICE Digital Voice Mail system.

• The VAU port assignment program (FF3 (ExtPort)# 47#) should be used to

configure digital ports connected to the PanaVOICE Voice Mail.

• The user can now dial

*73

to enable or disable the use of the Off-Hook

Monitor feature for 44-Series Telephones. When the user dials

*73

the first

time, the display reads

Monitor OFF

and the Off-Hook Monitor feature

cannot be used. When the user dials *73 a second time, the display reads

Monitor ON

and the Off-Hook Monitor can be used.

• The ISDN Inter-Digit Timer has been changed from a fixed length of 6

seconds to a fixed length of 4 seconds. This decreases the time the system
waits to determine if all digits are dialed before outdialing digits.

• The CPC version number display format has been changed to indicate the

product ID, version number and release date. For example, this release will
display as follows when

ON/OFF CONF 7777

is entered:

-EX 2.00 09-97

«
...
353
354
355
356
357
...
»

Summary of Contents for VB-44210G











































































































































































































































































































































































































Reviews:

No comments

Related manuals for VB-44210G

Brand: Samsung Pages: 32

Brand: 3Com Pages: 84

SuperStack 3 NBX

Brand: 3Com Pages: 496

Brand: 3CX Pages: 15

Ascotel Office 135

Brand: Aastra Pages: 2

Brand: GAI-Tronics Pages: 24

Brand: GAI-Tronics Pages: 20

Brand: Uniden Pages: 36

Brand: Hama Pages: 75

Brand: Karel Pages: 13

Brand: PHOTON Pages: 48

Brand: Swissvoice Pages: 103

CONVERSip Edge 300

Brand: Vertical Pages: 48

Brand: Teac Pages: 38

Brand: RAM Pages: 22

Brand: Nortel Pages: 56

Brand: Matosio Pages: 37

Brand: Uniden Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands