Panasonic VB-44210G User Manual Download Page 188 | Manualshive

Page: 188 / 394

background image

Chapter 4. Key Telephone Features

Section 700 - Operation

4-72

DBS Manual - Revised April 2000

DBS-2.3/9.2-700

Considerations

• The system does not send the offhook signal under the following

conditions:

- During a conference call

- While the called extension is on hold

- During a call on a CO line for which there is no line key on the called

extension.

Offhook Voice Announce (OHVA)

(All Versions)

Description

You can interrupt a busy extension when making an Intercom Call, and then
use the Off-Hook Voice Announce (OHVA) feature make an announcement
that only the called party can hear. You can also transfer a held call to a busy
extension after making the announcement using this feature.

Operation

To make an OHVA:

1. Pick up the handset.

2. Dial the desired extension number.

If the extension is busy, your phone issues busy tone.

3. Press

“5.”

• “CONF XXX YYY” (where “XXX” is the calling extension and

“YYY” is the receiving extension) appears on the display if you call a
busy extension.

• “CONF XX YYY” (where “XX” is the line number and “YYY” is the

extension) appears on the display if you call an extension that is
speaking with an outside line.

• The

EXT

LED flashes.

• “Voice Announce” appears on the called extension’s display.

«
...
186
187
188
189
190
...
»

Summary of Contents for VB-44210G











































































































































































































































































































































































































Reviews:

No comments

Related manuals for VB-44210G

Brand: Xblue Networks Pages: 241

Brand: Guardian Pages: 16

CRUISER2 HSF002

Brand: Jabra Pages: 2

Brand: Vicon Pages: 16

EVERPURE CONSERV LT-S

Brand: Pentair Pages: 20

Brand: Scitec Pages: 1

Brand: MagicBox Pages: 44

Brand: Gigaset Pages: 28

ONECONCEPT 10029361

Brand: Chal-tec Pages: 29

Brand: VTech Pages: 16

Titan Illuminated Crossing Telephone

Brand: GAI-Tronics Pages: 14

151 Musiccenter

Brand: Burmester Pages: 20

Brand: VTech Pages: 51

Brand: Wideye Pages: 24

Amplidect 295 SOS-Pro

Brand: Geemarc Pages: 2

Brand: Geemarc Pages: 31

Brand: Geemarc Pages: 58

Brand: Boss Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands